longnt.blogg.se

1. Wingoneer skypro high speed usb spi programmer software download#
2. Wingoneer skypro high speed usb spi programmer serial#
3. Wingoneer skypro high speed usb spi programmer software#
4. Wingoneer skypro high speed usb spi programmer series#
5. Wingoneer skypro high speed usb spi programmer download#

The programmer has multiple protections for the external power supply: The external power can be powered by a cell phone charger or charge pal can be seen everywhere. It can be connected to an external power supply 5V-5.5V 500MA for multipile programming. All chips do not need external power supply. VCC 120MA-320MA overcurrent protection continuously adjustable IO communication signal voltage continuously adjustable 1.2V-3.6V VCC voltage 1.2-6.5V 64 levels adjustable

Wingoneer skypro high speed usb spi programmer series#

25 series / EMMC in-circuit programming with a maximum clock frequency of 40MHZ-50MHZ Stable and reliable 8-Pins in-circuit programming ISP interface, the wire Length is more than 30CM, and it can communicate reliably at 25MHZ. All pins have a maximum operating frequency of 50MHZ and high reliability. 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB2.0 HS 480MHZ transmission (please note: before buying, make sure the chip models you want to program are in the support list!) NAND EMMC supports maximum capacity up to 256G

Wingoneer skypro high speed usb spi programmer serial#

Ultra-high cost performance, suitable for small batch programming below 5000, also suitable for developers and professional maintenance personnel.Ģ4/25/26/93 serial EEPROM, 27/28/29/36/37/39/49/50 EPROM, Paged EPROM,įLASH memory (NOR, NAND, SPI NAND, EMMC, NVRAM, SRAM, CPLD (GAL), etc.

Wingoneer skypro high speed usb spi programmer software#

User-friendly Software Interface, easy to use, more functions, easy to upgrade software Cool appearance, low power consumption, excellent work stability. Remarkable performance, ultra fast programming speed, very small and portable. Design focused on high-capacity memories programming. Fully open source programming adapter and competitive price. Ultra speed universal 56-pins powerful pindrivers programmer, no adapter required for any DIL devices. XGecu T56 Universal Programmer 56 Pin DriversSupport 20000+ ICs for Nor Flash / NAND Flash / EMMC (please note: before buying, make sure the models you want to program are in the support list!)

Wingoneer skypro high speed usb spi programmer download#

(If you cannot download or downloading speed is very slow, please send message to us, we will send to your mail box)

Wingoneer skypro high speed usb spi programmer software download#

I hope in someone's advice because i really hit a wall here.XGecu T56 Latest software download link: (will be updated in the future) Maybe there is a protection sistem with the vega cards that blocks everything if someone bricks the card? I'm really puzzled because the stock bios is correctly written in the chip so i don't really understand what's going on. Maybe if i manage to set the chip as another model with 256 kb size it will work.ĮDIT2:ways but I tried to flash the bios with the SPI programmer in many still no results. The bios chip is detected by the flashing software as a GigaDevice 25Q41 which has a rom size of 512 Kb.

This led me to belive that there is a problem with the flashing. Then if i use -i again it show test pass but i noticed that the rom size shown is 80000 while it should be 40000 for a 256 kb bios. If i use amdvbflash -i it shows test fail the first time. Do you think i need the 1.8 V adapter with this one or it adaps the voltage on it's own? I don't want to risk it and burn the bios chip.ĮDIT: The CH341A works but i still have some problems: I manage to flash the chip with the original bios but the card still isn't recognized by the pc. If i get one of those cheap SPI programmers should i be able to make it work again?ĮDIT: By doing amdvbflash -ai i found out that the previous owner flashed a rx 480 bios in the card. I then tried to use amdvbflashWin tool downloaded from techpowerup and i am able to use the -f flag to force the flash but i still get the 0FL01 error and it says Rom not erased. I tried using the -f flag to force the flash but it says that -f option is not supported in external version of the tool. I downloaded the most recent bios for this card from the vga bios repository and tried to flash it with the following command:īut i get an SSID mismatch error and a 0FL01 error I'm using the integrated graphics of the cpu to be able to boot into windows 7. I tried to recover it with amdvbflash tool from Igor's lab but to no avail. The previous owner tried to flash it with a Vega 64 bios and bricked it. Hi, i'm new to this forum and i hope someone will be kind enough to lend me a hand.